@ Wuchtbrumme
So sieht's beim FUNKTIONIERENDEN System aus:
Last login: Sat Feb 16 14:55:49 on console
MBP:~ MBP$ ifconfig -a
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0<> mtu 1280
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet6 fe80::21b:63ff:fe9b:5599%en0 prefixlen 64 scopeid 0x4
inet 192.168.1.101 netmask 0xffffff00 broadcast 192.168.1.255
ether 00:1b:63:9b:55:99
media: autoselect (10baseT/UTP <half-duplex>) status: active
supported media: autoselect 10baseT/UTP <half-duplex> 10baseT/UTP <full-duplex> 10baseT/UTP <full-duplex,hw-loopback> 10baseT/UTP <full-duplex,flow-control> 100baseTX <half-duplex> 100baseTX <full-duplex> 100baseTX <full-duplex,hw-loopback> 100baseTX <full-duplex,flow-control> 1000baseT <full-duplex> 1000baseT <full-duplex,hw-loopback> 1000baseT <full-duplex,flow-control> none
fw0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 4078
lladdr 00:1c:b3:ff:fe:93:fc:6c
media: autoselect <full-duplex> status: inactive
supported media: autoselect <full-duplex>
en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether 00:1e:52:72:89:62
media: autoselect (<unknown type>) status: inactive
supported media: autoselect
ppp0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1492
inet 80.171.110.46 --> 213.191.89.45 netmask 0xff000000
MBP:~ MBP$
MBP:~ MBP$ netstat -rn
Routing tables
Internet:
Destination Gateway Flags Refs Use Netif Expire
default 213.191.89.45 UGSc 7 0 ppp0
80 ppp0 USc 1 17 ppp0
127 127.0.0.1 UCS 0 0 lo0
127.0.0.1 127.0.0.1 UH 1 6 lo0
169.254 link#4 UCS 0 0 en0
192.168.1 link#4 UCS 2 0 en0
192.168.1.1 0:21:63:8:20:9c UHLW 0 37 en0 1150
192.168.1.101 127.0.0.1 UHS 0 0 lo0
192.168.1.255 link#4 UHLWb 3 161 en0
213.191.89.45 80.171.110.46 UH 8 0 ppp0
Internet6:
Destination Gateway Flags Netif Expire
::1 link#1 UHL lo0
fe80::%lo0/64 fe80::1%lo0 Uc lo0
fe80::1%lo0 link#1 UHL lo0
fe80::%en0/64 link#4 UC en0
fe80::21b:63ff:fe9b:5599%en0 0:1b:63:9b:55:99 UHL lo0
ff01::/32 ::1 U lo0
ff02::/32 fe80::1%lo0 UC lo0
ff02::/32 link#4 UC en0
MBP:~ MBP$
So sieht's beim NICHT FUNKTIONIERENDEN System aus:
Last login: Fri Dec 21 07:04:33 on console
MBP:~ ebe$ ifconfig -a
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0<> mtu 1280
fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078
lladdr 00:1c:b3:ff:fe:93:fc:6c
media: autoselect <full-duplex> status: inactive
supported media: autoselect <full-duplex>
en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether 00:1e:52:72:89:62
media: autoselect (<unknown type>) status: inactive
supported media: autoselect
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet6 fe80::21b:63ff:fe9b:5599%en0 prefixlen 64 scopeid 0x6
inet 192.168.1.52 netmask 0xffffff00 broadcast 192.168.1.255
inet 192.168.1.101 netmask 0xffffff00 broadcast 192.168.1.255
ether 00:1b:63:9b:55:99
media: autoselect (10baseT/UTP <half-duplex>) status: active
supported media: autoselect 10baseT/UTP <half-duplex> 10baseT/UTP <full-duplex> 10baseT/UTP <full-duplex,hw-loopback> 10baseT/UTP <full-duplex,flow-control> 100baseTX <half-duplex> 100baseTX <full-duplex> 100baseTX <full-duplex,hw-loopback> 100baseTX <full-duplex,flow-control> 1000baseT <full-duplex> 1000baseT <full-duplex,hw-loopback> 1000baseT <full-duplex,flow-control> none
ppp0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1492
inet 80.171.108.40 --> 213.191.89.45 netmask 0xff000000
MBP:~ ebe$ netstat -rn
Routing tables
Internet:
Destination Gateway Flags Refs Use Netif Expire
default 192.168.1.1 UGSc 5 0 en0
80 ppp0 USc 1 0 ppp0
127 127.0.0.1 UCS 0 0 lo0
127.0.0.1 127.0.0.1 UH 0 4 lo0
169.254 link#6 UCS 0 0 en0
192.168.1 link#6 UCS 2 0 en0
192.168.1.1 0:21:63:8:20:9c UHLW 5 16 en0 1172
192.168.1.52 127.0.0.1 UHS 0 0 lo0
192.168.1.101 127.0.0.1 UHS 0 0 lo0
192.168.1.255 ff:ff:ff:ff:ff:ff UHLWb 3 60 en0
213.191.89.45 80.171.108.40 UH 0 0 ppp0
Internet6:
Destination Gateway Flags Netif Expire
::1 link#1 UHL lo0
fe80::%lo0/64 fe80::1%lo0 Uc lo0
fe80::1%lo0 link#1 UHL lo0
fe80::%en0/64 link#6 UC en0
fe80::21b:63ff:fe9b:5599%en0 0:1b:63:9b:55:99 UHL lo0
ff01::/32 ::1 U lo0
ff02::/32 ::1 UC lo0
ff02::/32 link#6 UC en0
MBP:~ ebe$
Das sind für mich leider weitestgehend böhmische Dörfer. Ich hoffe, Ihr könnt damit was anfangen?
„was tust Du denn, um eine Verbindung in das Internet herzustellen?“
Oben in der Leiste ist ein Ethernt-Zeichen. Das klicke ich an. Dann erscheint mein „Mit Alice verbinden“. Das klicke ich an. Dann identifiziert er. Dauert höchstens wenige sec. Dann zeigt er die ablaufende Verbindungszeit an. Damit ist er „drin“ – aber eben nicht richtig.
Mal 'ne ganz dumme Frage: Kann da was an meinem OS X kaputt sein?
Gruß Insektenbauer