1. Diese Seite verwendet Cookies. Wenn du dich weiterhin auf dieser Seite aufhältst, akzeptierst du unseren Einsatz von Cookies. Weitere Informationen

D-Link DAP-1160 Access Point total langsam :/ Hilfe !

Dieses Thema im Forum "WLAN, Airport & TimeCapsule" wurde erstellt von AtticMike, 18.11.08.

  1. AtticMike

    AtticMike Tydemans Early Worcester

    Dabei seit:
    23.10.07
    Beiträge:
    393
    Hallo Mädels.

    Irgendwie ist nach dem Wechsel zum DAP-1160 meine Verbindung noch schlechter als vorher mit meinem USB Stick.

    Kennt sich jemand damit aus?

    Habe folgende Einstellungen zur Auswahl:

    Wireless Modes
    Access Point Mode

    AP Client Mode <-- Nutze ich gerade

    Bridge Mode

    Bridge with AP Mode

    Repeater Mode

    WISP Client Router Mode

    WISP Repeater Mode


    Erklährungen:

    Wireless Modes
    Access Point Mode


    In Access Point mode, the DAP-1160 acts as a central connection point for any computer (client) that has a 80.11g
    or backward-compatible 80.11b wireless network adapter and is within range of the AP. Clients must use the same
    SSID (wireless network name) and channel as the AP in order to connect. If wireless security is enabled on the AP,
    the client will need to enter a password to connect to the AP. Multiple clients can connect to the AP at the same time
    in Access Point mode.


    AP Client Mode

    In AP Client mode, the DAP-1160 acts as a wireless network adapter for your Ethernet-enabled device (such as a
    game console or a TV set-top box). Connect your Ethernet-enabled device to the AP using an Ethernet cable. AP
    Client mode can support multiple wired clients.

    Bridge Mode

    In Bridge mode, the DAP-1160 wirelessly connects seperate LANs that can’t easily be connected together with a cable.
    For example, if there are wired LANs separated by a small courtyard, it would be expensive to bury cable between the
    two sides. A better solution is to use two DAP-1160 units to wirelessly connect the two LANs. In Bridge mode, both
    DAP-1160 units do not act as APs.
    Note: Bridge Mode is not completely specified in Wi-Fi or IEEE standards. It can only work using other DAP-1160
    units. Communication with other APs (even other D-Link APs) is not guaranteed.

    Bridge with AP Mode

    Bridge with AP mod is the same as Bridge mode, but it also acts as an AP. Clients with wireless network adapters
    can wirelessly connect to the AP and then connect to the other LAN that the DAP-1160 bridges to.
    Note: Bridge with AP Mode is not completely specified in WiFi or IEEE standards. It can only work using other DAP-
    1160 units. Communication with other APs (even other D-Link APs) is not guaranteed.

    Repeater Mode

    Repeater mode increases the range of your wireless network by extending the wireless coverage of another AP or
    wireless router. The APs and wireless router (if used) must be within range of each other. Make sure that all clients,
    APs, and the wireless router all use the same SSID (wireless network name) and channel.

    WISP Client Router Mode

    In WISP Client Router mode, the DAP-1160 wirelessly connects to a WISP (Wireless Internet Service Provider) AP.
    In this mode, the DAP-1160 also acts as a router for wired clients on your LAN and provides NAT (Network Address
    Translation) and a DHCP server to generate IP addresses for wired clients. NAT and the DHCP server allow many
    computers to share the same wireless Internet connection.
    An example scenario is a WISP subscriber that wants to access their WISP account using wired computers. The wired
    computers connect to the DAP-1160, which provides NAT, and then connects to the WISP AP.

    WISP Repeater Mode

    In WISP Repeater mode, the DAP-1160 wirelessly connects to a WISP (Wireless Internet Service Provider) AP. In
    this mode, the DAP-1160 also acts as a router for both wireless and wired clients on your LAN. WISP Repeater mode
    provides NAT (Network Address Translation) and a DHCP server to generate IP addresses for both wireless and wired
    clients. NAT and the DHCP server allow many computers to share the same wireless Internet connection.
    An example scenario is a WISP subscriber that wants to use their WISP account in their house, but the signal from the
    outdoor WISP AP isn’t strong enough to reach all of the areas in the house. The DAP-1160 can extend the signal from
    the outdoor WISP AP and provide access for any wireless clients in the house. In addition, wired clients can connect
    to the DAP-1160, thus accessing the outdoor WISP AP.

    Ich connecte derzeit mit einem Kabel vom Mac Pro zum Acess Point von D-Link.

    30 KB Downloads mit 26 Mbit sind sehr happig.

    Warum habe ich zum Acess Point gegriffen? Die USB Adapter Software sorgte für Abstürze des Macs...

    Freue mich über jegliche Hilfe.
     
  2. Bananenbieger

    Bananenbieger Golden Noble

    Dabei seit:
    14.08.05
    Beiträge:
    24.567
    You made my day. :-D

    Nutzt Du den DAP als Basisstation oder verbindest Du Deinen Mac mit dem DAP zu einem anderen Access-Point?
     
    AtticMike gefällt das.
  3. AtticMike

    AtticMike Tydemans Early Worcester

    Dabei seit:
    23.10.07
    Beiträge:
    393
    sorry... ^^

    pretty used to write in english because of my relatives ...

    gonna keep the word :p
     
  4. AtticMike

    AtticMike Tydemans Early Worcester

    Dabei seit:
    23.10.07
    Beiträge:
    393
    Also.

    Thomson Kabel zu Internetumwandlerbox geht zum D-Link Router mit der Bezeichnung kA. Gleichzeitig auch ein W-Lan Router.

    Mein Access Point tut eigentlich das was mein USB-Stick getan hat. Nur gerne hätte ich mehr als 30 KB :/ Bzw nen tolleres Surf-Erlebnis :(
     
  5. Bananenbieger

    Bananenbieger Golden Noble

    Dabei seit:
    14.08.05
    Beiträge:
    24.567
    Hmm. AP Client Mode sollte dann richtig sein. Kannst aber auch mal den Bridge Mode (ohne AP) ausprobieren.
     
  6. AtticMike

    AtticMike Tydemans Early Worcester

    Dabei seit:
    23.10.07
    Beiträge:
    393
    geht nicht, kann ich kein Netzwerk auswählen.

    Hab mal dem Teil ne dynamische IP gegeben. Mal sehen was das jetzt gibt.

    Doofe IDee :D

    Jetzt komm ich net mehr in die Settings :D

    Im Repeater Modus macht der nun 1500 kb :D

    Ey, die Dinger kriegt man nur durch Tests erkundet :D
     
    #6 AtticMike, 18.11.08
    Zuletzt bearbeitet: 18.11.08

Diese Seite empfehlen