- Registriert
- 08.04.08
- Beiträge
- 43
Hallo zusammen,
Ich habe ein Problem mit meiner zweiten internen Festplatte und brauche Hilfe.
Ich habe ein Macbook Pro 15 Zoll von Anfang 2011 mit einer internen 1,5 TB HDD von Toschiba und einer SSD anstatt des früheren Superdrive Laufwerks. Mein System läuft natürlich auf der SSD, aber viele zusätzliche Daten speichere ich einfach auf der zweiten internen Festplatte. Nun ist es schon ein paar Mal vorgekommen, dass mein System plötzlich sagte, ich könne nicht mehr auf diese Platte schreiben, allerdings immernoch lesen. Nach Backup, neu formatieren und alles wieder aufspielen funktionierte immer alles wieder für ein paar Wochen. Nun aber plötzlich nicht mehr. Die Platte wird einfach nicht mehr angezeigt, bzw. im Festplatten Dienstprogramm nur ausgegraut. Da ich mich leider nicht damit auskenne, würde ich mich über Hilfe freuen. Brauche ich eine neue interne Festplatte oder kann ich die irgendwie noch retten? Ich habe mal die SMART Werte ausgelesen, kann nur nichts damit anfangen und hänge sie unten an.
Freue mich über jeden Tipp.
Besten Dank,
Chris
Mod-Info (double_d)
Bitte schließe solche langen Reports zukünftig in Code-Tags ein.
Das erhöht die Lesbarkeit ungemein und führt auch bei der Betrachtung auf Mobilgeräten oder in der App nicht zu seitenlangen Beiträgen.
Ich habe ein Problem mit meiner zweiten internen Festplatte und brauche Hilfe.
Ich habe ein Macbook Pro 15 Zoll von Anfang 2011 mit einer internen 1,5 TB HDD von Toschiba und einer SSD anstatt des früheren Superdrive Laufwerks. Mein System läuft natürlich auf der SSD, aber viele zusätzliche Daten speichere ich einfach auf der zweiten internen Festplatte. Nun ist es schon ein paar Mal vorgekommen, dass mein System plötzlich sagte, ich könne nicht mehr auf diese Platte schreiben, allerdings immernoch lesen. Nach Backup, neu formatieren und alles wieder aufspielen funktionierte immer alles wieder für ein paar Wochen. Nun aber plötzlich nicht mehr. Die Platte wird einfach nicht mehr angezeigt, bzw. im Festplatten Dienstprogramm nur ausgegraut. Da ich mich leider nicht damit auskenne, würde ich mich über Hilfe freuen. Brauche ich eine neue interne Festplatte oder kann ich die irgendwie noch retten? Ich habe mal die SMART Werte ausgelesen, kann nur nichts damit anfangen und hänge sie unten an.
Freue mich über jeden Tipp.
Besten Dank,
Chris
Code:
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01ABC...
Device Model: TOSHIBA MQ01ABC150
Serial Number: 92C9P45WT
LU WWN Device Id: 5 000039 442583a23
Firmware Version: AQ001U
User Capacity: 1,500,301,910,016 bytes [1.50 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Thu Apr 19 23:40:09 2018 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Disabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 377) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 3555
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 22088
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 066 066 000 Old_age Always - 13780
10 Spin_Retry_Count 0x0033 253 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 8487
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 172
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 115
193 Load_Cycle_Count 0x0032 075 075 000 Old_age Always - 259839
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 31 (Min/Max 14/44)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 248
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 253 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
222 Loaded_Hours 0x0032 093 093 000 Old_age Always - 3069
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 245
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 13541 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 13541 occurred at disk power-on lifetime: 13780 hours (574 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 30 78 8d 0b 40 Error: UNC 48 sectors at LBA = 0x000b8d78 = 757112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 40 68 8d 0b 40 00 07:59:07.553 READ DMA EXT
25 00 40 68 8d 0b 40 00 07:59:04.187 READ DMA EXT
25 00 40 68 8d 0b 40 00 07:59:00.820 READ DMA EXT
25 00 40 68 8d 0b 40 00 07:58:57.454 READ DMA EXT
2f 00 01 10 00 00 00 00 07:58:57.453 READ LOG EXT
Error 13540 occurred at disk power-on lifetime: 13780 hours (574 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 30 78 8d 0b 40 Error: UNC 48 sectors at LBA = 0x000b8d78 = 757112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 40 68 8d 0b 40 00 07:59:04.187 READ DMA EXT
25 00 40 68 8d 0b 40 00 07:59:00.820 READ DMA EXT
25 00 40 68 8d 0b 40 00 07:58:57.454 READ DMA EXT
2f 00 01 10 00 00 00 00 07:58:57.453 READ LOG EXT
60 40 48 68 8d 0b 40 00 07:58:54.092 READ FPDMA QUEUED
Error 13539 occurred at disk power-on lifetime: 13780 hours (574 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 30 78 8d 0b 40 Error: UNC 48 sectors at LBA = 0x000b8d78 = 757112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 40 68 8d 0b 40 00 07:59:00.820 READ DMA EXT
25 00 40 68 8d 0b 40 00 07:58:57.454 READ DMA EXT
2f 00 01 10 00 00 00 00 07:58:57.453 READ LOG EXT
60 40 48 68 8d 0b 40 00 07:58:54.092 READ FPDMA QUEUED
60 40 40 a8 9d 70 40 00 07:58:54.091 READ FPDMA QUEUED
Error 13538 occurred at disk power-on lifetime: 13780 hours (574 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 30 78 8d 0b 40 Error: UNC 48 sectors at LBA = 0x000b8d78 = 757112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 40 68 8d 0b 40 00 07:58:57.454 READ DMA EXT
2f 00 01 10 00 00 00 00 07:58:57.453 READ LOG EXT
60 40 48 68 8d 0b 40 00 07:58:54.092 READ FPDMA QUEUED
60 40 40 a8 9d 70 40 00 07:58:54.091 READ FPDMA QUEUED
60 40 38 e8 01 71 40 00 07:58:54.080 READ FPDMA QUEUED
Error 13537 occurred at disk power-on lifetime: 13780 hours (574 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 48 78 8d 0b 40 Error: UNC at LBA = 0x000b8d78 = 757112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 40 48 68 8d 0b 40 00 07:58:54.092 READ FPDMA QUEUED
60 40 40 a8 9d 70 40 00 07:58:54.091 READ FPDMA QUEUED
60 40 38 e8 01 71 40 00 07:58:54.080 READ FPDMA QUEUED
60 40 30 68 ae 74 40 00 07:58:54.067 READ FPDMA QUEUED
60 40 28 68 9d 70 40 00 07:58:54.066 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Mod-Info (double_d)
Bitte schließe solche langen Reports zukünftig in Code-Tags ein.
Das erhöht die Lesbarkeit ungemein und führt auch bei der Betrachtung auf Mobilgeräten oder in der App nicht zu seitenlangen Beiträgen.