• Apfeltalk ändert einen Teil seiner Allgemeinen Geschäftsbedingungen (AGB), das Löschen von Useraccounts betreffend.
    Näheres könnt Ihr hier nachlesen: AGB-Änderung
  • Was gibt es Schöneres als den Mai draußen in der Natur mit allen Sinnen zu genießen? Lasst uns teilhaben an Euren Erlebnissen und macht mit beim Thema des Monats Da blüht uns was! ---> Klick

[MacBook Pro] Beachball -> Festplatte ?

daherr

Granny Smith
Registriert
11.02.14
Beiträge
15
Hallo,

Ich hätte da ein kleines Problem. Gestern ist mir mein MacBook plötzlich abgeschmiert und ich musste es neu starten.
Beim starten tauchte ein Ordner mit einem Fragezeichen auf, sprich, dass das Startvolume nicht gefunden wurde. Nach ein paar Minuten und dem Booten mit Alt Taste ging es wieder, seitdem is das MacBook einfach unfassbar langsam. So langsam, dass ich diesen Text mit einem anderen Gerät schreiben muss. Ständig der beachball und Nichteinmal das Surfen klappt noch.

Auch das starten dauert extrem lange, manchmal hängt er sich auch dabei auf. Alle gängigen resets wurden gemacht, sowie allen Optionen des festplattendienstprogramms.

Für mich klingt das irgendwie ziemlich nach der Festplatte, zumal es noch die Originale ist und noch nie ausgetauscht wurde.
Ich habe ein MacBookPro Mid 2009, das in den letzten Jahren exzessiv genutzt wurde und auch schon mehrer Stürze überlebt hat.

Glaubt ihr auch, dass es an der Festplatte liegen könnte?
Der SMART Status ist jedoch ok, was mich ein wenig wundert.

/Edit: Hab hier mal die kompletten SMART Attribute reingepackt, verstehen tue ich da leider nicht soviel:



Code: 
/Users/davidherrmann/Downloads/SMARTReporter-DEMO.app/Contents/Resources/smartctl --tolerance=permissive --smart=on -a disk0

smartctl 6.3 2014-07-26 r3976 [x86_64-apple-darwin14.0.0] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Fujitsu MJA BH
Device Model:     FUJITSU MJA2250BH FFS G1
Serial Number:    K94DT9A2EUJM
LU WWN Device Id: 5 00000e 0441897d3
Firmware Version: 00810020
User Capacity:    250,059,350,016 bytes [250 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 3f
SATA Version is:  SATA 2.6, 1.5 Gb/s
Local Time is:    Fri Jun  3 16:04:43 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)    Offline data collection activity
                    was never started.
                    Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)    The previous self-test routine completed
                    without error or no self-test has ever
                    been run.
Total time to complete Offline
data collection:         (  783) seconds.
Offline data collection
capabilities:              (0x7b) SMART execute Offline immediate.
                    Auto Offline data collection on/off support.
                    Suspend Offline collection upon new
                    command.
                    Offline surface scan supported.
                    Self-test supported.
                    Conveyance Self-test supported.
                    Selective Self-test supported.
SMART capabilities:            (0x0003)    Saves SMART data before entering
                    power-saving mode.
                    Supports SMART auto save timer.
Error logging capability:        (0x01)    Error logging supported.
                    General Purpose Logging supported.
Short self-test routine
recommended polling time:      (   2) minutes.
Extended self-test routine
recommended polling time:      ( 111) minutes.
Conveyance self-test routine
recommended polling time:      (   2) minutes.
SCT capabilities:            (0x003d)    SCT Status supported.
                    SCT Error Recovery Control supported.
                    SCT Feature Control supported.
                    SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   100   100   046    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0005   100   100   030    Pre-fail  Offline      -       0
  3 Spin_Up_Time            0x0003   100   100   025    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   094   094   000    Old_age   Always       -       25300
  5 Reallocated_Sector_Ct   0x0033   100   100   024    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   100   100   047    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   100   100   019    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0032   069   069   000    Old_age   Always       -       15601
10 Spin_Retry_Count        0x0013   100   100   020    Pre-fail  Always       -       0
12 Power_Cycle_Count       0x0032   097   097   000    Old_age   Always       -       17081
160 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   099   099   000    Old_age   Always       -       335363113280
193 Load_Cycle_Count        0x0032   075   075   000    Old_age   Always       -       515895
194 Temperature_Celsius     0x0022   100   100   000    Old_age   Always       -       40 (Min/Max 6/51)
195 Hardware_ECC_Recovered  0x001a   100   100   000    Old_age   Always       -       0
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   253   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x000f   100   100   060    Pre-fail  Always       -       0
203 Run_Out_Cancel          0x0002   100   100   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x003e   200   200   000    Old_age   Always       -       0
254 Free_Fall_Sensor        0x0032   100   100   000    Old_age   Always       -       11041

SMART Error Log Version: 1
ATA Error Count: 9 (device log contains only the most recent five errors)
    CR = Command Register [HEX]
    FR = Features Register [HEX]
    SC = Sector Count Register [HEX]
    SN = Sector Number Register [HEX]
    CL = Cylinder Low Register [HEX]
    CH = Cylinder High Register [HEX]
    DH = Device/Head Register [HEX]
    DC = Device Command Register [HEX]
    ER = Error register [HEX]
    ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 9 occurred at disk power-on lifetime: 9632 hours (401 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  14 51 01 00 00 00 e0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  f9 01 01 00 00 00 e0 00      00:00:06.882  SET MAX SET PASSWORD [OBS-ACS-3]
  f5 00 00 00 00 00 e0 00      00:00:06.881  SECURITY FREEZE LOCK
  ec 00 00 00 00 00 e0 00      00:00:06.879  IDENTIFY DEVICE
  00 00 01 01 00 00 00 ff      00:00:06.775  NOP [Abort queued commands]

Error 8 occurred at disk power-on lifetime: 9631 hours (401 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  14 51 01 00 00 00 e0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  f9 01 01 00 00 00 e0 00      00:00:04.587  SET MAX SET PASSWORD [OBS-ACS-3]
  f5 00 00 00 00 00 e0 00      00:00:04.586  SECURITY FREEZE LOCK
  ec 00 00 00 00 00 e0 00      00:00:04.584  IDENTIFY DEVICE
  00 00 01 01 00 00 00 ff      00:00:04.481  NOP [Abort queued commands]

Error 7 occurred at disk power-on lifetime: 9629 hours (401 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  14 51 01 00 00 00 e0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  f9 01 01 00 00 00 e0 00      00:00:04.716  SET MAX SET PASSWORD [OBS-ACS-3]
  f5 00 00 00 00 00 e0 00      00:00:04.715  SECURITY FREEZE LOCK
  ec 00 00 00 00 00 e0 00      00:00:04.713  IDENTIFY DEVICE
  00 00 01 01 00 00 00 ff      00:00:04.610  NOP [Abort queued commands]

Error 6 occurred at disk power-on lifetime: 9629 hours (401 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  14 51 01 00 00 00 e0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  f9 01 01 00 00 00 e0 00      00:00:04.713  SET MAX SET PASSWORD [OBS-ACS-3]
  f5 00 00 00 00 00 e0 00      00:00:04.712  SECURITY FREEZE LOCK
  ec 00 00 00 00 00 e0 00      00:00:04.710  IDENTIFY DEVICE
  00 00 01 01 00 00 00 ff      00:00:04.606  NOP [Abort queued commands]

Error 5 occurred at disk power-on lifetime: 9615 hours (400 days + 15 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  14 51 01 00 00 00 e0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  f9 01 01 00 00 00 e0 00      00:00:04.592  SET MAX SET PASSWORD [OBS-ACS-3]
  f5 00 00 00 00 00 e0 00      00:00:04.591  SECURITY FREEZE LOCK
  ec 00 00 00 00 00 e0 00      00:00:04.589  IDENTIFY DEVICE
  00 00 01 01 00 00 00 ff      00:00:04.485  NOP [Abort queued commands]

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%     14610         -
# 2  Short offline       Completed without error       00%     14608         -

SMART Selective self-test log data structure revision number 1
SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.


Grüße
David
 
Zuletzt bearbeitet:
meru

meru

Winterbanana
Registriert
30.09.06
Beiträge
2.187
Hatte ich erst auch, ist die Festplatte die langsam verreckt.
Wenn du noch in der Konsole Disk: I/O error (X = irgendeine Zahl) hast solltest du Handeln!

mfg Meru
 
Du musst dich einloggen oder registrieren, um hier zu antworten.
2003-2024 Apfeltalk | Made on a Mac
Oben Unten