Hallo Zusammen,
dank für die schnelle Antwort.
Das System wurde ist auf dem neuesten Stand:
Anbei die SMART-Werte:
smartctl 6.5 2016-05-07 r4318 [Darwin 15.6.0 x86_64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke,
www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi/HGST Travelstar 5K750
Device Model: APPLE HDD HTS547550A9E384
Serial Number: J2250050HVSS5C
LU WWN Device Id: 5 000cca 640da424c
Firmware Version: JE3AD70E
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Fri Feb 24 12:30:08 2017 CET
SMART support is: Available - device has SMART capability.
SMART support is: Disabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 45) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 139) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 062 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0
3 Spin_Up_Time 0x0007 180 180 033 Pre-fail Always - 1
4 Start_Stop_Count 0x0012 098 098 000 Old_age Always - 3360
5 Reallocated_Sector_Ct 0x0033 098 098 005 Pre-fail Always - 61
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0
9 Power_On_Hours 0x0012 092 092 000 Old_age Always - 3790
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 3039
160 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 098 098 000 Old_age Always - 1894080577596
193 Load_Cycle_Count 0x0012 073 073 000 Old_age Always - 273722
194 Temperature_Celsius 0x0002 176 176 000 Old_age Always - 34 (Min/Max 13/46)
195 Hardware_ECC_Recovered 0x000a 054 054 000 Old_age Always - 83886208
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 64
197 Current_Pending_Sector 0x0022 001 001 000 Old_age Always - 2664
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
223 Load_Retry_Count 0x000a 100 100 000 Old_age Always - 0
254 Free_Fall_Sensor 0x0032 089 089 000 Old_age Always - 2966
SMART Error Log Version: 1
ATA Error Count: 1575 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1575 occurred at disk power-on lifetime: 3789 hours (157 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 40 38 f6 71 07 Error: UNC 64 sectors at LBA = 0x0771f638 = 124909112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 78 f2 71 40 00 02:31:21.163 READ DMA EXT
25 00 00 78 f2 71 40 00 02:31:17.830 READ DMA EXT
25 00 00 78 f2 71 40 00 02:31:14.483 READ DMA EXT
25 00 10 48 a9 20 40 00 02:31:14.463 READ DMA EXT
25 00 00 78 f2 71 40 00 02:31:11.119 READ DMA EXT
Error 1574 occurred at disk power-on lifetime: 3789 hours (157 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 40 38 f6 71 07 Error: UNC 64 sectors at LBA = 0x0771f638 = 124909112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 78 f2 71 40 00 02:31:17.830 READ DMA EXT
25 00 00 78 f2 71 40 00 02:31:14.483 READ DMA EXT
25 00 10 48 a9 20 40 00 02:31:14.463 READ DMA EXT
25 00 00 78 f2 71 40 00 02:31:11.119 READ DMA EXT
2f 00 01 10 00 00 00 00 02:31:11.118 READ LOG EXT
Error 1573 occurred at disk power-on lifetime: 3789 hours (157 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 40 38 f6 71 07 Error: UNC 64 sectors at LBA = 0x0771f638 = 124909112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 78 f2 71 40 00 02:31:14.483 READ DMA EXT
25 00 10 48 a9 20 40 00 02:31:14.463 READ DMA EXT
25 00 00 78 f2 71 40 00 02:31:11.119 READ DMA EXT
2f 00 01 10 00 00 00 00 02:31:11.118 READ LOG EXT
60 10 a8 48 a9 20 40 00 02:31:07.656 READ FPDMA QUEUED
Error 1572 occurred at disk power-on lifetime: 3789 hours (157 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 40 38 f6 71 07 Error: UNC 64 sectors at LBA = 0x0771f638 = 124909112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 78 f2 71 40 00 02:31:11.119 READ DMA EXT
2f 00 01 10 00 00 00 00 02:31:11.118 READ LOG EXT
60 10 a8 48 a9 20 40 00 02:31:07.656 READ FPDMA QUEUED
60 00 a0 78 f2 71 40 00 02:31:07.654 READ FPDMA QUEUED
60 08 98 f8 30 0d 40 00 02:31:07.640 READ FPDMA QUEUED
Error 1571 occurred at disk power-on lifetime: 3789 hours (157 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 40 38 f6 71 07 Error: UNC at LBA = 0x0771f638 = 124909112
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 10 a8 48 a9 20 40 00 02:31:07.656 READ FPDMA QUEUED
60 00 a0 78 f2 71 40 00 02:31:07.654 READ FPDMA QUEUED
60 08 98 f8 30 0d 40 00 02:31:07.640 READ FPDMA QUEUED
25 00 00 78 ea 71 40 00 02:31:04.307 READ DMA EXT
25 00 00 78 ea 71 40 00 02:31:00.973 READ DMA EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Danke
((
